Review the data on your extended networks However, a feature like that could make both new users and network administrators confused.Ĩ. It would be wonderful if you could "cross wire" the primary networks and extensions operating at 2.4 and 5 GHz. Additionally, a 5 Ghz Wi-Fi network is the only one that the 5 Ghz extension network may broadcast. Only 2.4 GHz primary wireless networks can be configured to repeat using the 2.4 GHz extension SSID. This means that you cannot use the 5 Ghz extension SSID on this extender to expand a 2.4 Ghz network. It should be noted that this extender does not permit connecting to both extended and extension Wi-Fi networks at the same time. The "Extended Network details" screen will appear after a brief wait, if you supplied the correct password, as demonstrated in the following step. You'll see the same "Checking the password" page that you saw for the 5 GHz password entry. Please double-check your password entry before clicking "Next" to avoid having to press RESET and start over. The primary 2.4 GHz network you are extending's password should be entered. Following that, you will be asked for its password, as shown next. One 2.4 GHz and one 5 GHz network can only be expanded by this range extender at once.Ĭhoose the 2.4 GHz network you want to extend from the list that is displayed by tapping or clicking on it. However, this time, since we've already extended a 5 Ghz wireless network above, the screen only displays the in-range 2.4 Ghz wireless networks. If you input the right password above and the "Checking the password" prompt has cleared, you will then be taken back to the "Choose the wireless network you'd like to expand" screen, as shown in the screen shot below. To continue with Belkin WiFi Extender Setup, choose the 2.4 GHz Wi-Fi network that you want to extend (if any). Warning: Your password will be displayed plainly on this screen as you type it in, so be sure to complete this step in a place where no one will see it except you.Ĭheck your typing for accuracy after you've entered all the password's characters.Ħ. Networkįor the 5 GHz wireless network you are expanding, enter your main network password. The extender will then be forced to re-scan for available networks to extend if you tap or click the "Refresh" button above.ĥ. Move the point nearer to your main wireless access point to fix this. Therefore, their signals can be insufficient. If your network(s) are physically too far away from this range extender, they could not be shown here. Skip to step 5 when that information has been entered. Press the "I don't see my network here" option in that case, and then follow the on-screen directions to manually enter your network's SSID, security type, and password. Please take note that your network may be hidden if it does not appear in the list. Decide which 5 GHz wireless network you want to expand. The "Choose the wireless network you'd like to expand" screen is shown in your browser after a little pause, as shown in the next step.Ĥ. This tells the extender to look for repeatable wireless networks in both the 2.4 and 5 GHz bands. On the belkin.range page, click the "Get Started" button. Go to in your web browser if the setting start screen does not show. We may easily join it on the iPad Air by tapping it once.įollowing successful connection, your computer instantly assumes the range extender's default IP address, which is 192.168.206.2, as shown in the next image. You won't be requested for a password because it is OPEN. Once you've done configuring, this access point will no longer be active because it is only active during setup. It was on our iPad Air, as shown in the image below. Then, look for the "tup" wifi network on your PC or mobile device. To configure the wireless range extender and continue with Belkin WiFi Extender Setup, log in to it. Observe the directions in our post on Belkin Wireless Range Extender Reset Instructions.ģ. However, if you purchased a used gadget, you should RESET it just in case the previous owner did not remove their modified settings. If you just bought this extender, skip to step 3 now. Next, return the extender to its factory default settings. Connect the power to the Belkin Extender.Ģ.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |